16'x32' Buildingw/ full loftManufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manua
4. Assemble another beam.Step 8 Install 2nd Floor Loft BeamBeam6. Place the beam into the beampocket. Secure in place with16d sinkers.2x4 Wall Brace1.
Beam2x4 Tie Plate5. Tongue and groove flooring does not cover 48" width. Install a 1x4-8' white pine boardfiller after the last row of floor
SidewallLoft FloorPanel #7Panel #6Step 10 Install Front & Back Wall Trim1. Cut 1x4-10' trim boards to length for the front corners. Install t
Siding ExtendsBelow Bottom PlateStep 11 Assemble Rear Roof Gable ContinuedReapply SidingFront Wall8. Install the gable frames numbered 9 and 10 to the
84-1/2" Long 2x4with Angle Block2x4x82-1/4"2nd LayerEnd With Blue Mark4. Locate (4) four 2x4s that are 84-1/2" long and have an angle
3. Locate gable panels 4 and 5.Remove the siding from thesepanels. The siding panels aretacked to the walls with a fewnails.1-1/2" SidingFillersS
Step 16 Assemble Trusses1. Lay 2x6 truss parts inside the 2x4 blocks. One end of the 81-3/4" long 2x6 boards have a bluemark. Place these ends t
1-1/2"floor2x4 Tie Plate2x6 Truss Plate2x6 Truss PlateStep 17 Set Gables and 2x6 Truss Plate4. Layout 2x6 plate for trusses. Important: Startthe
2-1/2" Screw2x6 SoffitBlock1x3 Board2x6 TrussPlate2x6 Truss Plate2. Secure trusses to 2x6 truss plates with 2x6metal hangers. Nail metal hanger t
Building Tip: Ridge vent provides idealventilation, preventing heat or moisture fromdamaging your building or its contents.Ridge vent providesideal ve
measurefrom hereWhen measurements are given for board length,it is from the longest side of the board.ToolListHammer & Phillips ScrewdriverFraming
1x6 Gable Trim1. Install 82-1/4" long 1x6 white pine trim boards at the top of the gable overhangs. Installthe end with the blue marking at the r
1x6 Keystone48-1/2" Door TrimStep 23 Install Door Trim1. Install 85" long 1x4 white pine boards as door trim on each side of the door openin
Step 24 Install Optional Barn DoorsLeft DoorInstall Sliding Door Latch4. Before you fasten the hinges to the doortrim, temporarily prop the doors in t
Material Needed 29 bdl. roof shingles, 15 pcs. roof edge and 3 rolls felt paper.Packing ListQty. Qty.24 4 x 8 3/8" LP Exterior Siding 30 2x6 12&q
Stud SpacingXXXXXX8' - 0" PlatesNOTE: In westernstates all wall studsare 92-1/4" in length!Step 1 Assemble Rear Wall2. Install 92-5/8&q
16"15-1/4"Step 2 Assemble Front Door Wall2. Cut (2) two 7-1/2" x 48" long fillers fromOSB sheathing that was used to wrap thepalle
*83-3/8" When usingwestern wall studs.*Step 2 Assemble Front Door Wall Continued5/8" OSB Filler83-3/4" long 2x4Pre-cut 2x4Step 3 Build
Frame Door OpeningFrame Window Openingfor 18" x 36" Aluminum Window36"2x4 Blocking35-3/4"Optional Door & Window OpeningsWindow
6. Install (2) two full width siding panels.7. Repeat numbers 1 thru 4 to build another wall frame. DO NOT apply siding.16"11-3/4"16"3.
4. Repeat Steps 4 thru Step 6 to assemble the opposite sidewalls.XXXXXX8' - 0" Wall Plate16"15-1/4"16"Top Wall PlateTreated B
Step 7 Set Wall Panels1. Set the left sidewall, with the beam support, panel and the 96" long back wallpanel. Secure the corner together with 16d
Comments to this Manuals