Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright
18-1/4"7. Gather 2x4s and components shown below andassemble the door wall. Use 10d sinkers.Step 7 Assemble Front Wall Panel1. Cut (2) two 2x4-6&
16. Cut the cutoff siding panel, from step number 13,to extend 3-1/2" beyond the wall frame.Cut EdgeStep 7 Assemble Front Wall Panel ContinuedSid
Top PlateWall Stud3-1/2"56-1/2" Tie Plate56-1/2" Tie Plate141-1/2"141-1/2"XXXXXX7. Install a 36" x 77-1-4" panelwi
3. Install a 1x3-72" board acrossthe top of the side trim.1x3-72" Trim1x4-72" TrimStep 9 Set Lower Walls1. Secure wall panels together
Step 10 Install Trim1. Install (2) two 1x3-62" long trim boards flush with the top of the front wall. Use 8d galv. nails.2. Install 1x4-75 3/4&q
3. Using 1-1/2" hanger nails, install the right hangers to the 2x6 tie plate.The top hanger flange should line up with the 'X' mark.2x6
Wood GussetLeft GableFront WallNote: The center truss willnot have a bottom cord.Step 12 Set Trusses Continued24"4. Install the trusses over the
2' x 4' OSB4' x 4' OSB2' x 4' OSB2. Install OSB loft flooring over the rear and front trusses. Notch the flooring around
10'x12'10'x16'Building LengthRoof Shingles 7 bdl. 10 bdl.Roof 'drip' Edge 6 pcs. 7 pcs.Material DescriptionBuilding Tip:
Step 15 Install Doors & Hardware4. Before you fasten the hinges to the doortrim, temporarily prop the doors in theopening. Leave a space at the to
Tongue EdgeLAP EdgeTool ListHammer & Phillips ScrewdriverFraming Square & LevelHand or Circular SawPower Drill/ScrewdriverMeasuring Tape2 - 8&
Roof Materialby OwnerRoof Shingles 7 bdl.Roof 'drip' Edge 6 pcs.Qty. Qty.4 Wall Plates 120 "8 Truss - Bottom Cords 116 1/4" 4 1x4
10' - 0" Building WidthNail the 2x4s to the 4x4runners to keep the 2x4frame from moving.It is important that the floor belevel and square. B
Wood Gusset with 2x4 BlockStep 1 Assemble Trusses2x4 Truss Half2x4 BlockTop GussetLower Gusset2x4-116-1/4" Bottom Cord1. Position (2) two half tr
Siding Extends3/4" Below PlateTip; To prevent gable studs frombeing knocked loose when nailingsiding, lay 2x4 OSB sheathing,supplied in kit, unde
1x4Trim2x3-47" BoardStep 3 Install Rear Gable Overhang & Trim3. Apply 1x4 white pine trim to gable. Install a 47" long 1x4 at the top of
6. Assemble the loft doors. The loft door frames aretemporarily held together with corrugated fasteners,this is the back side of the door frame. Place
Step 5 Install Gable Trim & Loft Doors3. Install 29-1/4" long 1x3 trim boards on each side of the loft door opening.Install a 43" long
AABBXXXXXXXXXXXXStep 6 Assemble Back Wall1. Position 68-1/2" and 65-1/2" long 2x4 boards together and indicate where the wall studswill be l
Comments to this Manuals